Sponsored By

A better way to make hay?A better way to make hay?

Putting up hay as baleage is an option for dealing with wet fall harvest conditions.

November 11, 2019

6 Min Read
closeup of wrapped bales of hay
HIGHER QUALITY: The shorter time period needed to make hay as baleage decreases the impact of weather on harvest.

Wet conditions created major challenges this year for producers to put up hay for winter forage needs. Shorter days and cooler fall temperatures add to the challenge of putting up dry hay. Cattle producers may want to consider making baleage instead of baling the hay as an option for dealing with cold and wet weather.

The following information is provided by Iowa State University Extension beef cattle specialist Denise Schwab, ag engineer Brian Dougherty and agronomist Brian Lang.

Making baleage is a method of preserving forage where bales are made at a higher moisture content than dry hay and then sealed in plastic wrap for storage. The high moisture level and airtight environment causes the forage to ferment. The optimum moisture range for baleage is 40% to 50% dry matter, with an acceptable range of 35% to 60% DM.

Baling at proper moisture content is important for good fermentation. Forages baled at less than 40% moisture are more likely to have poor fermentation and greater mold production. At moisture levels greater than 65%, the chance of undesirable butyric acid fermentation increases.

Baleage offers several benefits

The time needed to cure forage for baleage is drastically reduced compared to production of dry hay, thus reducing the impact of weather on harvest. This is a significant advantage when trying to harvest forages in conditions that are poor for making dry hay. Less time needed to make baleage also leads to earlier and more frequent cuttings, which increases overall quality of the stored forage.

However, the higher moisture content makes bales considerably heavier. Bale size may need to be reduced to accommodate existing machinery. In many operations, round bale diameter is reduced 12 inches or more to keep bale weight within a manageable range for bale carriers, front-end loaders and feed mixing equipment.

Keep in mind that a 1,500-pound dry hay bale would weigh nearly 2,600 pounds at 50% DM. Baleage bales need to be sized so your equipment can lift and transport them safely. Also, a smaller bale size will result in more total bales from a given field compared to dry hay, so it’s important to plan ahead to ensure adequate storage space is available.

Equipment needs

You may be able to use existing equipment to produce and feed baleage. An often-asked question is whether a conventional baler can be used for making baleage. The answer: It depends on the baler. Some newer balers can achieve sufficient bale density for making quality baleage. However, balers made specifically for baleage typically have modifications including heavy-duty bearings to handle extra weight and scrapers to prevent buildup of material on rollers and belts.

You should try to achieve a bale density of about 10 pounds DM per cubic foot when baling, which may not be possible with some baler models.

Some manufacturers offer "silage kit" upgrades that can be added to conventional balers. This may be worth considering if the baler is still in good condition. Another popular add-on to silage balers is a set of pre-cutter knives that process the hay into shorter lengths. A 4-inch cut length is recommended. This allows for greater bale density, less plastic usage, less feed waste in bale feeders and easier use of bales in a feed mixer. Consult the equipment manufacturer if you have specific questions about using your baler for making baleage.

The next equipment decision you need to make is how to wrap the bales in plastic. Bales can be wrapped individually on a bale wrapping table or can be wrapped in-line with a “tube” wrapper. A third option is to place the bales into individual bags that can be sealed by hand. Wrapping bales is faster than bagging, but it requires a bale wrapping machine. The advantage of the tube wrapper is that a conventional bale spear on a front-end loader can be used to load the bales into the wrapper.

Individual bale bags can be a good option if a bale wrapper isn’t available, but good bag fit is important. It’s critical that excess air is pushed out of the bag before sealing. It may require two people to twist the plastic tightly over the bale and tie it off. Both individually wrapped bales and bagged bales will require a bale grabber capable of lifting bales without puncturing the plastic if bales need to be moved or stacked after bagging.

Making high-quality baleage

Mowing with a mower-conditioner and laying the forage out in a wide swath is recommended. This will speed up the drying rate and can improve feed quality by reducing carbohydrate loss.

Bales should be made as densely as possible. This allows for more dry matter in the same bale volume and reduces oxygen content in the bale. The result will be better fermentation and less spoilage and heating. Reducing ground speed during baling can help produce more densely packed bales.

Bales should be tied with plastic twine or netwrap. Avoid using sisal twine as it contains chemical preservatives that can degrade plastic wrap over time. Netwrap has the advantage of creating a smoother bale surface and helps prevent coarse stems from poking through the plastic wrap. Wet bales can quickly lose their shape and become very difficult to handle and wrap. Thus, bales should be moved and wrapped as soon as possible after baling. This helps reduce heating and improves feed quality. Use of hay preservatives and inoculants shouldn’t be necessary if the bale is wrapped properly. Regardless of wrapping technique, plastic should be at least 6-mm thick to ensure good fermentation.

The bale storage site should be well-drained and free of sharp objects that could puncture the plastic wrap. Keep weeds under control and clean up any spoiled feed in the area to help prevent rodent and insect damage. Holes in the plastic should be covered as soon as possible with tape made specifically for patching holes.

Feeding considerations

Compared to dry hay from the same field, baleage production reduces DM and leaf loss during harvest, providing for increased protein and total digestible nutrients (TDN). Baleage also results in less waste at the feeder compared to dry hay in most cases. However, baleage will begin to spoil once exposed to air, so it is recommended that baleage be consumed within 48 to 72 hours of air exposure. Smaller bales consisting of less dry matter also increase the frequency in which bales must be delivered to cows.

The time it takes for baleage to completely ferment will vary depending on forage maturity at harvest and weather conditions. Wait six to eight weeks after harvest before feeding baleage, if possible. If a TMR mixer or other grinder is used to process bales, make sure the machine is capable of handling baleage. Grinding baleage requires a heavy-duty machine capable of withstanding tremendous forces. Keeping knives sharp will reduce wrapping in the mixer and tractor horsepower required for grinding.

Making baleage is an effective way of preserving wet hay. With good management and a bit of planning, it can produce feed of equal quality to silage placed in bags or bunkers. When deciding whether to make baleage instead of dry hay, consider the suitability of your equipment for harvesting, handling and feeding baleage. Hiring a custom operator can be a good option if you aren’t set up to make baleage with your own equipment. Also, consider where you will store the bales and how that will impact feeding operations.

For more information, see the Iowa Beef Center publication Making the Switch to Baleage, IBCR 202. 

Source: ISU, which is solely responsible for the information provided and is wholly owned by the source. Informa Business Media and all its subsidiaries are not responsible for any of the content contained in this information asset.


Subscribe to Our Newsletters
BEEF Magazine is the source for beef production, management and market news.

You May Also Like